Originally posted by phet_fresh
View Post
Announcement
Collapse
No announcement yet.
Nissan Thai-Thai
Collapse
X
-
Originally posted by phet_fresh View Post
Yeah! Engine swap to V8 and RWD conversion.
so How is going there? paste me your build page!Visit Bagriders.com for the best deals on Airride suspension.
Stbk123 - Instagram.
ViolentClique
Comment
-
Originally posted by mikey G View PostRWD!?
Originally posted by stbk View PostNot that good, mercedes is getting sold due to financial issues. i have a little project with the EK9 civic. but nothing fancy yet! hope to come down to thailand again next year. maybe january or february. i will give you a visit again then
Comment
-
Here is more update, about RWD concersion.
The rear suspension and LSD differential from skyline R32.
I cut some frame and build the new chassis for mounting the R32 rear suspension. It's almost finish, left the upper shock mounting.
Last edited by phet_fresh; 10-18-2014, 08:14 PM.
Comment
-
This is amazing! I never thought someone would rwd swap an altima. Great work![CENTER][url=http://www.stanceworks.com/forums/showthread.php?t=66924][color=red]e28 build thread[/color] [/url]
[img]http://i.imgur.com/hNTlNvf.jpg?2[/img]
Instagram: [url=https://instagram.com/divingboardlord/][color=red]@divingboardlord[/color][/url][/CENTER]
Comment
-
Originally posted by Robitussin View PostThis is amazing! I never thought someone would rwd swap an altima. Great work!
Comment
-
I here the motor came, it's 3uz
the hard thing is 3uz was lock by immobilizer key and the throttle be electronic.
My plan is swap the wire harness to 1UZ , first I have to start the motor with the cable throttle and wire harness of 1UZ.
there are some connector was different. The shock sensor, I use of JZ instead and the connetor of ign-coil. I swap only connector by the same terminal.
The transmission also chang to manual. I choose Mitsubishi Triton cause it's cheper from Toyota, but it had same flange as Toyota.
And the crank case need to change to front crank style.
Last edited by phet_fresh; 11-02-2014, 02:10 AM.
Comment
-
Finally I could start the motor 3UZ with the 1UZ ECU their wire harness.
So much love the V8 sound.
Last edited by phet_fresh; 11-06-2014, 07:52 AM.
Comment
-
Originally posted by mikey G View PostThis shit is BANANA'S!Originally posted by gearheaded View PostWow this is a whole nuther level of cool. RWD in this case is gonna be the bomb!Originally posted by aeok18109 View PostHmm. 3uz is similar to my power plant. 1uzfe. Trying to source a trans for mine lol.Originally posted by TruTaing View Post++
This should be a year project, will try my best.
Comment
-
Hello guys! Clutch just arrive a month ago.
I had bid the single carbon clutch ORC from Yahoo.jp.
It's EVO VII-VIII clutch, the work with my Mitsubishi transmission.
Yeah! I have a lot of work to do. Let check it.
First the diameter and the bolt hub is extreme different, and the starter gear also
But the starter gear is not a big deal, just remove from the old flywheel and lathe to the EVO flywheel
And the hub, I lathe it and welding all the hole with the hardest material.
And welding the stock spacer plate to the fly wheel to make it hard more, the result is below
And the last for the clutch issue, the bell housing.
Making measurement
And integrated the both bell, and measurement again
It is a little long, I will lathe it short and welding, tomorrow.
Lastly! after I tried with it and I also shoot few photo.
It's so beauty clutch, thought.
Enjoy your coffeeLast edited by phet_fresh; 01-20-2015, 05:40 AM.
Comment
Comment