Page 1 of 4 123 ... LastLast
Results 1 to 25 of 79

Thread: 1972 BMW 2002 Build

  1. #1
    Join Date
    Dec 2013
    Location
    Alberta Canada
    Posts
    27

    Default 1972 BMW 2002 Build

    Hey everyone,

    I am a long time lurker and have now decided to finally do a build thread on my 72 BMW 2002. Up in Canada clean 2002’s are not easy to find so I consider myself very lucky for ending up with this particular car. The previous owner’s uncle bought it new and it remained in the family until I took ownership. It came with the original keys, manuals, and is a factory air conditioned car. Needless to say I am quite pleased! When I first came out to look at the car, it had been sitting, unrunning, for 15 years in a garage. It looked a little sad. Since its a 2002 it does come with rust, but overall its a very straight unmolested car! Exaclty what I wanted. My goal for this car is too have a more powerful, reliable, cruising car that I can drive the wheels off of. This is how it was sitting for the last 15 years..





    Cleaned the engine up and put a new fuel pump in and it runs beautifully! So needless to say I had to drive her around.




    Here is some of the rust issues. Although old, the paint is in good condition and after polishing should look awesome. I am grateful that the rust is concealed to areas that aren’t on the the main body panels and therefore I have less bodywork ahead of me!




    Picked up some 15'' BBS Rims that I think should look good. More to come....

    Last edited by mini67; 02-25-2017 at 10:36 AM.

  2. #2
    Join Date
    Nov 2013
    Location
    Kitchener, Ontario
    Posts
    117

    Default

    Love a good 2002 project! I'd love to find one that clean in Ontario that won't break the bank.

  3. #3
    Join Date
    Dec 2013
    Location
    Alberta Canada
    Posts
    27

    Default

    Just finished up some rust work in the trunk and rockers so may as well show progress. The strut towers on these cars rust from the inside out so I had to cut out way more than it looked like but the inner tower was super solid so I did not touch it! I fabricated the patch from the roof of a scrap car and am pleased with the results.







    I also got all the nuts and bolts zinc dichromate plated which I highly recommend to anyone else dealing with rusty bolts!


    Also notice that hideous steering wheel? It was necessary to replace it with the legendary Momo Prototipo. This car actually would originally have had a thin three spoke wheel but it was long gone!




    When everything was nicely apart I decided it would be a good idea to polish the paint. It would have been repainted 20+ years ago but it looks amazing! Heres where it sits as of today. I still have to get the BBS RM's redone. I'm thinking of going with a gun-metal metallic. What do you guys think? Should I stick with the black?






  4. #4
    Join Date
    Jan 2016
    Posts
    24

    Default

    that o2 is turning out beautifully!

  5. #5
    Join Date
    Jul 2012
    Posts
    106

    Default

    coming along nicely!

  6. #6
    Join Date
    Jan 2012
    Location
    Munich
    Posts
    447

    Default

    Black is not a good mesh color for BBS RS. You dont see anything of the wheels which means you could run any other wheel too. Give them some shine!
    Quote Originally Posted by getamongst-it View Post

    Lower your expectations, you'll be much happier.
    Oh, and your car too.

  7. #7
    Join Date
    Apr 2014
    Location
    YEG
    Posts
    430

    Default

    Holy shit that paint looks damn good after only a polish.


    I/G: DeltaAlpha9

  8. #8
    Join Date
    Nov 2014
    Posts
    30

    Default

    loving the interior! great updates.

  9. #9
    Join Date
    Nov 2012
    Posts
    5

    Default

    Great job so far. I would maybe go with a white centre on those Rs's..

  10. #10
    Join Date
    Sep 2014
    Location
    Poland
    Posts
    6

    Default

    love this car

  11. #11
    Join Date
    May 2011
    Location
    Michigan
    Posts
    1,173

    Default

    Looking great!
    lamborfuckinghini

  12. #12
    Join Date
    Dec 2013
    Location
    Alberta Canada
    Posts
    27

    Default

    Here is a little video I made to show my progress so far. Hope you guys enjoy! I am not sure how to make it embedded in the forum.

    [media=youtube][/media]
    Last edited by mini67; 12-24-2016 at 10:53 PM.

  13. #13
    Join Date
    Aug 2011
    Posts
    854

    Default

    Damn. Awesome work!

    Very impressed with the rust repair.

    Also much respect for all that filthy cleaning!

    I know it sucks.

    Rs will look great. I agree you should get them refinished in silver!

    I really want to know what you paid for the car though.

  14. #14
    Join Date
    Dec 2016
    Location
    Netherlands
    Posts
    83

    Default

    And another 2002 on it's way to being saved, you're doing a great job!
    Cheers

  15. #15
    Join Date
    Dec 2013
    Location
    Alberta Canada
    Posts
    27

    Default

    Some of you who watched the video might have noticed a subtle battery bracket and hold down clamp in the trunk. I figured there might not be room in the engine bay after the engine swap so I decided to mount it there. At the moment I am just getting all the rear suspension components painted and ready to be installed. The diff on the left is a 3.91 Limited slip out of a E21 320is. The diff itself bolts in, however to do the swap you have to take the cover off a 2002 and adapt to the bigger CV joint holes. My 72 had an unvented cover, so I took a vented cover off a 75. Next you have to drill holes to mount the CV or change half of the CV’s to that from the E21.The e21 diff has m10 bolt holes and the 2002 cv’s are m8. See the problem? I am going to drill in the diff, this way I can always buy new cv joints and just bolt them right in, instead of having to make “special” CV joints out of a e21 and a 2002. Also I am going with the e21 rear drum brakes as well. They bolt right on and are 250mm which is an improvement over the 230mm stock 2002 drums. As you notice ALL the nuts and bolts went to the plater, and I mean ALL. I did get a little carried away but it is so shiny!







    Here is the limited slip on the left, If you look super carefully you will notice that it is incredibly gross. Notice the vented cover on the 2002 diff on right. And of course the magical S on the tag! Last picture is an unvented cover.





    I had the parts sandblasted and then brushed on POR15. I have heard only good stuff about the product however I am not totally happy with the look, but if it holds up that is more important! I am sure if it was sprayed it would have turned out better. Here is the stock 2002 drum inside the e21 drum







    Here is the finished Limited Slip. Pretty happy with the look, I did go a little crazy with getting bolts plated….





    Christmas presents to myself are the best! How did I know? Recaros…. The interior is slowly coming together! More to come...




  16. #16
    Join Date
    Dec 2016
    Location
    Turkey / Germany
    Posts
    1

    Default

    Subscribed! Also subscribed to your youtube channel. Looking good.

  17. #17
    Join Date
    Feb 2014
    Location
    SK, Canada
    Posts
    88

    Default

    Nice build! Cool to see a Sasky build on here.

  18. #18
    Join Date
    Aug 2015
    Location
    Essex/London - UK
    Posts
    180

    Default

    This is looking to be a great build. Can't wait to see this progress!

  19. #19
    Join Date
    Aug 2012
    Location
    Seattle , WA
    Posts
    99

    Default

    This looks awesome! She cleaned up real nice.

  20. #20
    Join Date
    Dec 2013
    Location
    Alberta Canada
    Posts
    27

    Default

    So I did a little bit of putting stuff together. Here is all the parts a rear brake and control arm assembly consists of. And then all nicely together! Looks way easier in pictures! The wheel bearings were not fun too install…







    The parts are accumulating…





    Here the 02 sits patiently waiting for even more parts. I figured I may as well do some polishing and put some trim on the car. Got a new classic style Bmw badge for the front as well. Looks awesome! Way better than the sticker that was on it before. Crazy how dusty stuff gets though….More to come…










  21. #21
    Join Date
    Oct 2011
    Location
    La Mirada, CA
    Posts
    4,085

    Default

    Wow, I love your attention to detail.

    This thing is going to be amazing when it is done!

  22. #22
    Join Date
    Jun 2016
    Posts
    3

    Default

    Brilliant work, my dude! Always wanted to do this with my 02 before it was hit.

  23. #23
    Join Date
    Sep 2015
    Location
    London, Uk
    Posts
    210

    Default

    Love the way this build is going, got a soft spot for 2002's. Keep up the good work, Look forward to seeing more.

    BMW E36 Touring Sport - http://www.stanceworks.com/forums/sh...ad.php?t=76178
    Instagram: @Vish399

  24. #24
    Join Date
    Dec 2013
    Location
    Alberta Canada
    Posts
    27

    Default

    Hello again,

    Thanks guys! I hope its going to be amazing when its done!

    Since my suspension order won’t be shipped for some time I decided to tackle the engine. The new heart is an M42. An inline 4, Dual overhead cam, 16 valve engine from a 1991 BMW 318is. Now although Webbers and a Cam can make the same power from the original engine and it would be super cool, I wanted something dependable and something that I could upgrade in the future to make even more power. The engine was looking a little gross and although I am probably not painting the engine bay, the engine itself definitely needed to be painted. So here is the original engine and its home for the last 45 years. Yikes, 45 years! These cars are getting old….





    Here is its replacement!





    And so begins the tear down.



    Painted the block with POR15, turned out alright



    Crazy rough casting on the valve cover. All solved by a quick trip to the sander.







    Here is some of parts that needed. I just have to sandblast and paint the timing chain covers and oil pan, then pick up my bolts from the platers and throw it all together! I still have lots of work ahead!





  25. #25
    Join Date
    Sep 2016
    Posts
    5

    Default

    That is so sweet man. Great restoration. I see that in one photo there is an Alberta plate on a bike? Are you in Sask or Alberta?

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •