Too much?

[M.Burroughs]

http://blankmediagroup.com/Pictures/Mike/E28-%20Rusty/aycharizzle.jpg

Can't decide. Obviously I need to lower it a little more, but we're talking purely poke.

[Exami]

I like, as more is more :devillook

Actually that is just right rims comes out but tyre stays in.. but issues while turning tyres?

[grippymonkey]

Looks about right... any more would be too much

[SeanDub]

I rike.

[M.Burroughs]

Now I have to figure out how to make the rears fit.

[rimtuck]

Looks good to me.
btw, how long til your car is eaten away? Looks tough though

[M.Burroughs]

A good 5 years minimum. Rust is slow.

[B Rod]

Now I have to figure out how to make the rears fit.

:eek Maybe I'm slightly out of the loop. Specs?

[driggers.a]

With the camber it'll be good, assuming it sits lower than that on the ground...

[M.Burroughs]

I'm gonna pic whore.

http://blankmediagroup.com/Pictures/Mike/Trips/SoWo%202009/mycar/_DSC3083%20as%20Smart%20Object-1%20copy.jpg

Hellatucked approved? :D


:(

[southpaw]

Uh may zing.

[Moose]

Jose and Jose B would approve! IMO if low enough it can be pulled off, but if it looks like most cars with that much poke (High) it is gonna look goofy.

[rimtuck]

the six is so sicks!!!!!

[M.Burroughs]

Jose and Jose B would approve! IMO if low enough it can be pulled off, but if it looks like most cars with that much poke (High) it is gonna look goofy.

Since when is anything I do "high"? ;)

[Moose]

Since when is anything I do "high"?

IDK your 6 has quite a bit of clearance, IIRC you only scraped once or twice driving from TN to NC. I may or may not be forgetting a few thousand times. You know what I mean though, when there is too much poke sometimes you cannot go low enough, those are 17's right?

[Ollie]

16s??

lower and more camber. I can dig a little extra poke every once in a while.

[M.Burroughs]

17s still. 16s are coming as soon as money frees up.

[Exami]

allways lowest is not the best.. on my mind when you start going "down & in" its wrong.
Rim should be coming out or fender so fender should be near rims but still tyre inside fender as you have on front now..

[schroedin]

I dig it, nice work. Good luck with the rears :rofl

[bjh102]

u know my thoughts.

[Skillz]

5mm less?
It could be perfect as is,but it's hard to say.
I would "roll" the front fender lip.the one that is | so it would go on with the line of the fender that comes \.I don't know if I made myself understood :rolleyes

Anyhow I trust it will be sick!

[TheStig]

Damn, thats alot of poke man. I kinda like it.

[notloEnuf]

I persoanlly think its just a bit much poke for the front. However still looks quite good.

[TheStig]

if you use a fender roller and try to pull a bit, will it fuck up the rust? :shifty

[notloEnuf]

if you use a fender roller and try to pull a bit, will it fuck up the rust? :shifty

It's ok another week of rain and it will be right back to good as rusted. :eyebrows

[TheStig]

It's ok another week of rain and it will be right back to good as rusted. :eyebrows

Verry true. I say go for it Mike, if not, I could always just put them on my car. :)

[notloEnuf]

i think a little bit of pull would make it titties.

[525iT_Feen]

How wide are those in front? 10? I can see it working with more drop. Its almost to much for my taste though.

[so steezy]

I think once the camber is dialed in, it will look awesome

[Ollie]

It's too much for my taste too but the car is rusted and at this point it's all about the fun and cool factors plus I'm sure it's still gonna look money. Roll, camber, n poke the shiii out of it.

BTW is it even possible to fuck up rust? lol

[M.Burroughs]

I don't think the rust can be hurt.

As for camber, I can't do much about it right now, but Austin is making me some fixed plates. I'm gonna bust out a metal bat and give the rears a happy ending massage. :cool

[notloEnuf]

I don't think the rust can be hurt.
I'm gonna bust out a metal bat and give the rears a happy ending massage. :cool

:alright

[frink84]

little too much poke, but thats me. i like seeing what crazy ideas come out of your garage no matter what

[Travis]

I'm gonna have to go ahead and agree with everything that has been said in this thread. Thats a lot of poke, maybe a little too much for my taste, once dialed in it will look great, i love seeing new stuff coming from your garage :cool

[Pswirley]

Can't decide until I see these new plates. I think 5mm less would yah mazin

[FluidMotorUnion]

Sick.

[greenbeem93]

Too much? Nothing on that car will be too much...lol

[M.Burroughs]

I was thinking to myself, how could I go even lower on the 18s? I rub in the back and can't run as it is.

Well, what if I mutilated the rears to make it work, and simply removed the front fenders, but put the hood back on for good measure?


EH!?

[B Rod]

Anything is a possibility with that car. Do it, and show us some pics...haha.

[frink84]

remove front fenders! yes!!!!!!!

[Travis]

You shouldn't even have to ask haha.

[Burn535i]

i would need to see more pics to decide but so far it looks good

[schroedin]

Oh hay. Pictures of the car with no fenders?

[Tuck&Poke]

just sit that shit on the tire and call it a day

[Chris@MemoryFab]

I'm gonna pic whore.

http://blankmediagroup.com/Pictures/Mike/Trips/SoWo%202009/mycar/_DSC3083%20as%20Smart%20Object-1%20copy.jpg

Hellatucked approved? :D


:(

OMG:o

I can you please send me a high res version of this
id love that as my desktop:)

[boostAbear]

OOOO me rikey!! I dont think its too much, id like to see the backs tho

[Flavourless]

Not feeling it. Its just a little to much poke for my liking. Maybe with a little camber adjustment I may come around ;)

[Towelie]

looks good if anything just pull the fender a bit